标题: FLUENT周期性边界 [打印本页] 作者: Carter 时间: 2013-8-5 11:45 标题: FLUENT周期性边界 画好 非结构网格,以图示的对称面将其网格镜像。得到该网格的对称网格,将两个非结构网格合并,生成的Mesh文件导入Fluent。为什么周期性边界不能设置成周期性边界条件。[img][/img]作者: 吕璐 时间: 2013-8-6 13:21
周期性边界参考设置方法,首先,在gambit中,将需要的周期性面定义为wall,一般为两个面。然后,在fluent中,输入命令1.输入grid,(输入几何模型命令)2.输入modify-zones,(修改边界条件命令)3.输入list-zones,(列表出现边界条件信息,你可以看到定义的边界条件信息,其中关注你定义的周期性面wall)4.输入make-periodic,(将需要的边界面修改成周期性边界条件,这里输入前面定义的序号,两个面)5.输入yes,(然后出现,Rotational periodic?(if no,translational)[yes]信息,输入yes选择周期性,例如你的模型是一个圆形体)6.输入yes,(出现creat periodic zones?[yes]信息,输入yes即可。)作者: 张荣建 时间: 2013-8-6 15:48
周期性条件需要 在做网格输出时设置好,可参考icem中帮助文件设置周期性网格,然后到fluent中才能设置好作者: Carter 时间: 2013-8-6 15:55
嗯,我在ICEM中设置周期性边界面为WALL. 生成网格后,定义该一对面为周期性边界面。操作步骤:> grid/modify-zones/make-periodicPeriodic zone [()] 22Shadow zone [()] 23Rotational periodic? (if no, translational) [yes] yesCreate periodic zones? [yes] yes Warning: differing number of faces on these threads. zone 22: matched 1733 out of 12642 faces. zone 23: matched 1733 out of 16127 faces.Error: Failed to make zones periodic.作者: Carter 时间: 2013-8-6 15:57
嗯,我在ICEM中设置周期性边界面为WALL. 生成网格后,定义该一对面为周期性边界面。操作步骤:> grid/modify-zones/make-periodic Periodic zone [()] 22 Shadow zone [()] 23 Rotational periodic? (if no, translational) [yes] yes Create periodic zones? [yes] yes Warning: differing number of faces on these threads. zone 22: matched 1733 out of 12642 faces. zone 23: matched 1733 out of 16127 faces. Error: Failed to make zones periodic.该如何去解决?作者: 谢清乐 时间: 2013-8-6 19:01
在icem中划分周期性网格时候,首先需要设置周期面,然后对周期性面上的点进行对应。最后倒入fluent中才能按照你的方法设置周期性边界。具体的方法网上很多,你可以看看。作者: Carter 时间: 2013-8-7 09:20
明白啦,谢谢!作者: Carter 时间: 2013-8-7 09:20
明白啦,谢谢作者: Carter 时间: 2013-8-7 09:21
明白啦,谢谢