- \"在Ansys中,参数化编程进行灵敏度分析时,碰到错误“The volume 1 is defined!”。 其中同一个程序在运行是：有时候1还会变成20。这该怎么解决呢？ \" (1篇回复)
- 在Ansys中,碰到错误提示的内容是：The input volumes do not meet the conditions required for the VGLUoperation . No new entities were created . The VOVLAP operation is a possible alternative.该怎么解决？ (1篇回复)
- 在Ansys中,碰到错误“Keypoint 2 belongs to line 4 and cannot be moved”,这是什么错误？ (1篇回复)
- 在Ansys仿真时,遇到提示：CLEAR, SELECT, and MESH boundary condition commands are not possible after MODMSH.这是什么问题？ (1篇回复)
- 在ANSYS仿真时,提示solid model data is contaminated。这是什么问题？ (1篇回复)
- 在Ansys仿真时,用命令流建模的时候遇到提示：The drag direction (from the keypoint on drag line 27 that is closest to a keypoint KP of the given area 95) is orthogonal to the area normal at that KP. Area cannot be dragged by the VDRAG command.这是什么意思？ (1篇回复)
- 在Ansys仿真时,遇到提示：L1 is not a recognized PREP7 command, abbreviation, or macro. This command will be ignored。这是怎么回事？ (1篇回复)
- 在Ansys中,遇到提示：Keypoint 1 is referenced by only one line. Improperly connected line set for AL command.这是怎么回事？ (1篇回复)
- Ansys仿真时,遇到提示：No *CREATE for *END. The *END command is ignored,这是怎么回事？ (1篇回复)
- 在Ansys中,使用*TREAD时,有的时候明明看文件好好的,可是却出现 *TREAD end-of-file in data read. 这是怎么回事？ (1篇回复)
- 在Ansys中,设置LATT后,仿真提示ESYS is not valid for line element.这是怎么回事？ (1篇回复)
- 在Ansys中,设置LATT后,仿真提示ESYS is not valid for line element.这是怎么回事？ (1篇回复)
- \"在Ansys中,碰到提示：The value of UX at node 10224 is 416889864. It is greater than the current limit of 1000000. This generally indicates rigid body motion as a result of an unconstrained model. Verify that your model is properly constrained。这是什么问题？ (1篇回复)
- 在Ansys中,碰到错误：This model requires more scratch space than available, currently 8026545 words ( 31 MB). ANSYS was not able to allocate more memory to proceed. Please shut down other applications that may be running or increase the virtual memory (1篇回复)
- 在Ansys中,碰到错误Large negative pivot value ( -8.419662714E-03 ) in Eqn.system. May be because of a badtemperature-dependent material property used in the model.这可能是什么原因造成的？ (1篇回复)
- Ansys计算时候出现：Input/output error on unit=9.Possible full disk ,在一些论坛看到转换磁盘格式ntfs,转换后还是不行,我的ansys11.0安装在D盘,工作目录为E盘（30G大小）,另外输出窗口提示“for better cpu performace increase memory by 296mb using -m option”,该怎么解决？ (1篇回复)
- 在Ansys中,碰到“Topolgical degeneracy detected for ASBA command.Try modifying geometry slightly or loosening the tolerance(BTOL command).If BTOL is relaxed ,be sure to change the tolerance back to the default after operation”,这是什么意思？ (1篇回复)
- 在Ansys中,碰到警告和错误：“*** WARNING *** SUPPRESSED MESSAGE CP = 1312.641 TIME= 16:51:48 An error has occurred writing to the file = 12 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors (1篇回复)
- 在Ansys中,碰到错误Volume11 could not be swept because a source and a target area could not be determined automatically。please try again...,这是什么原因？ (1篇回复)
- 在Ansys中,碰到提示“Volume 1 cannot be meshed. 208 location(s) found where non-adjacent boundary triangles touch. Geometry configuration may not be valid or smaller element size definition may be required.”。这是什么问题？ (1篇回复)
