777 预览 \"在Ansys中,参数化编程进行灵敏度分析时,碰到错误“The volume 1 is defined!”。 其中同一个程序在运行是：有时候1还会变成20。这该怎么解决呢？ \"

2948 预览 在Ansys中,碰到错误提示的内容是：The input volumes do not meet the conditions required for the VGLUoperation . No new entities were created . The VOVLAP operation is a possible alternative.该怎么解决？

619 预览 在Ansys中,碰到错误“Keypoint 2 belongs to line 4 and cannot be moved”,这是什么错误？

752 预览 在Ansys仿真时,遇到提示：CLEAR, SELECT, and MESH boundary condition commands are not possible after MODMSH.这是什么问题？

3172 预览 在ANSYS仿真时,提示solid model data is contaminated。这是什么问题？

1555 预览 在Ansys仿真时,用命令流建模的时候遇到提示：The drag direction (from the keypoint on drag line 27 that is closest to a keypoint KP of the given area 95) is orthogonal to the area normal at that KP. Area cannot be dragged by the VDRAG command.这是什么意思？

2688 预览 在Ansys仿真时,遇到提示：L1 is not a recognized PREP7 command, abbreviation, or macro. This command will be ignored。这是怎么回事？

6824 预览 在Ansys中,遇到提示：Keypoint 1 is referenced by only one line. Improperly connected line set for AL command.这是怎么回事？

715 预览 Ansys仿真时,遇到提示：No *CREATE for *END. The *END command is ignored,这是怎么回事？

4622 预览 在Ansys中,使用*TREAD时,有的时候明明看文件好好的,可是却出现 *TREAD end-of-file in data read. 这是怎么回事？

957 预览 在Ansys中,设置LATT后,仿真提示ESYS is not valid for line element.这是怎么回事？

1319 预览 在Ansys中,设置LATT后,仿真提示ESYS is not valid for line element.这是怎么回事？

6554 预览 \"在Ansys中,碰到提示：The value of UX at node 10224 is 416889864. It is greater than the current limit of 1000000. This generally indicates rigid body motion as a result of an unconstrained model. Verify that your model is properly constrained。这是什么问题？

2210 预览 在Ansys中,碰到错误：This model requires more scratch space than available, currently 8026545 words ( 31 MB). ANSYS was not able to allocate more memory to proceed. Please shut down other applications that may be running or increase the virtual memory

3323 预览 在Ansys中,碰到错误Large negative pivot value ( -8.419662714E-03 ) in Eqn.system. May be because of a badtemperature-dependent material property used in the model.这可能是什么原因造成的？

797 预览 Ansys计算时候出现：Input/output error on unit=9.Possible full disk ,在一些论坛看到转换磁盘格式ntfs,转换后还是不行,我的ansys11.0安装在D盘,工作目录为E盘（30G大小）,另外输出窗口提示“for better cpu performace increase memory by 296mb using -m option”,该怎么解决？

1361 预览 在Ansys中,碰到“Topolgical degeneracy detected for ASBA command.Try modifying geometry slightly or loosening the tolerance(BTOL command).If BTOL is relaxed ,be sure to change the tolerance back to the default after operation”,这是什么意思？

2192 预览 在Ansys中,碰到警告和错误：“*** WARNING *** SUPPRESSED MESSAGE CP = 1312.641 TIME= 16:51:48 An error has occurred writing to the file = 12 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors

4448 预览 在Ansys中,碰到错误Volume11 could not be swept because a source and a target area could not be determined automatically。please try again...,这是什么原因？

3952 预览 在Ansys中,碰到提示“Volume 1 cannot be meshed. 208 location(s) found where non-adjacent boundary triangles touch. Geometry configuration may not be valid or smaller element size definition may be required.”。这是什么问题？